PRACH Basic-1

-

Home               LTE              NB-IoT             5G(NR-NSA)

In this section we will learn about PRACH and its basics as well as interview questions.
             

To obtain the UL synchronization, a preamble is send by UE to gNB over PRACH channel. As LTE, in 5G NR also there are 64 preambles defined in each time frequency PRACH accession.

After the cell search process, UE has obtained DL synchronization with cell, so UE can receive DL data. But UE can perform UL transmission only when it obtains UL synchronization with the cell. The UE forms the connection with cell and obtains UL synchronization through random access procedure. The main purpose is:
  • Achieve uplink synchronization between eNB and UE
  • Obtain the resource from Msg3 (obtain uplink grant, the uplink resource request)
  • Assign CRNTI(unique identity) to Device (TCRNTI will promote as CRNTI once contention resolved)

It is not capable if UE is using broadcasting or always on synchronization mechanism. The UL synchronization process should meet the below criteria:
  • The process of synchronization should happen only when there is immediate necessary.
  • The synchronization should be dedicated to only a specific device(UE).
The fundamental difference here in 5G NR RACH from LTE RACH would lie just before RACH preamble gets transmitted. This is because of beam forming which would be supported by default in NR. When NR operates on beam forming mode, UE needs to detect and select the best beam for RACH process. The beam selection process could be the fundamental difference between LTE and NR RACH process.

Before the initiation of RA (random access) procedure layer1 i.e physical layer at UE receives set of PBCH/SS blocks.

Based on RSRP measurement of SS/PBCH blocks decides on 1 PBCH/SS index and then performs RA procedure. The relationship between SS/PSCH block and PRACH resources is totally based on higher layer parameter ssb-perRACH-OccasionAndCB-PreamblesPerSSB.

How does Network know exactly when UE will transmit the RACH? 

 Network knows when UE will transmit the RACH even before UE sends it as Network tells (using PRACH Configuration Index) UE when the UE is supposed to transmit the RACH.

How to determine which preamble format to use?

PRACH Configuration Index determines the Preamble Format that is to be used. 



Who determines PRACH Configuration index?

eNB determines it through prach-Configuration IE in SIB2 (In the Case of LTE. for ENDC, MSG (LTE) initial attach).

From where UE can find RACH parameter information during HO?

UE can find RACH info from RRCConnectionReconfig msg. 

How many RACH-Preamble can be used?
64 PRACH preambles (which is divided in Preambles group A & B as well as contention free for HO) are available theoretically in total, but the number of the preambles available in a specific condition is determined by a couple of SIB2 parameters (for LTE Case). 

How UE decides about where and when it needs to send RACH Request:-

UE decides it on the basis of parameters received in SIB2 PRACH configurations (for LTE Case).
UE can use six Resource blocks for sending the RACH Request.

How many types of Msg3 on CCCH?

There are two types of Msg3 on CCCH. RRCconnectionRequest ( which used for initial access and random access) RRCconnectionReestablishmentReq ( which used for after RLF detected).



In the next section we will learn more about RACH. 
So keep reading……. And Stay tune……………



Pinal Dobariya………..





Reference:
3GPP TS 38.321
3GPP TS 38.300
3GPP TS 38.213


Comments

  1. Anonymous1 May 2020 at 11:55

    I guess most of the content is based on LTE. Would you mind extending to NR also?

    ReplyDelete

Post a Comment

Popular posts from this blog

Soft Handover vs Hard Handover

-
Home                 LTE                NB-IoT            5G(NR-NSA) Now before we move to other things like measurements in handover, handover decision, handover procedure, handover interruption time, and mobility robustness optimization, let us take a look into difference between soft handover and hard handover. Soft Handover Hard Handover The handover in which radio links are added and removed in a way that MS always keeps at least one radio link to the UTRAN is known as soft handover. The handover in which all the old radio links in MS are removed before the new radio links are established is known as hard handover. This can also be simplified as make before break This can also be simplified as break before make As call drop rate is lower this handover is used to lower the rate of call drop. In this case higher rates of call drops are found Why soft handover is not included
Read more

5G Deployment Option-3/3a/3x

-
Image
Home                 LTE                NB-IoT            5G(NR-NSA)   Hi Guys today we are learning about 5G deployment options, if you want to know more about other 5G deployment option please  click here Option 3: EN-DC (EUTRA-NR Dual Connectivity) Option 3 represents a network having both LTE and NR radio access, but using only the EPC core of LTE to route the Control signals. In this option, LTE is used as the control plane anchor for NR, and both LTE and NR are used for user data traffic.(user plane). It could also be called as Non-Standalone (NSA) NR in Evolved Packet System. The only difference between Options 3 and 3A is based on whether the user plane data is sent to NR directly or via the LTE RAN. This standardization was concluded in 3GPP Rel-15. This is a possible first step in the migration towards 5G-SA. This option will be most attractive for operators which have early deployments of 5G NR access systems in areas where legacy eNB and EPC a
Read more

DRX (Discontinuous Reception)

-
Image
Home                 LTE                NB-IoT            5G(NR-NSA)   What is DRX and DRX active period? What channels does it monitor in active period? Data transmission between UE and their base stations(eNodeB) uses radio frames with10ms duration, where in each radio frame consists of 10 1ms( 1 frame=10ms duration=10 subframe) subframes. Physical Downlink Control Channel (PDCCH) at the beginning of each subframe indicates whether there is data for UE to receive or not. Devices has to monitor these PDCCHs in each subframe so that it can find out whether they carry any data to receive. Because devices do not receive data in every subframe, this monitoring process naturally leads to high battery consumption.  What is the purpose of DRX? The main purpose of DRX is to lower battery consumption when there is no UL/DL data. means, when there is no traffic(DL/UL) that time devices enter into sleep mode (with RF module turned off) for some period of time as configured by
Read more

5G Deployment Option-7/7a/7x

-
Image
Home                 LTE                NB-IoT            5G(NR-NSA) Hi Guys today we are learning about 5G deployment options, if you want to know more about other 5G deployment option please  click here Option 7: Deployment Option 7 represents a deployment scenario in which the Next Generation Core (NGC) will be used with a mixture of LTE and NR radio.  Next Generation signaling will be used but it will be routed via the LTE RAN because the LTE network is more fully built out and thus more reliable for handling signaling.  Options 7 and 7a differ on whether the user plane data is sent to NR directly or via the LTE RAN. 7/7A/7X require an eLTE upgrade of the existing LTE network at the start. (Difference is UP path Non Standalone ( Dual Connectivity 4G/5G ) Option 7/7A: NSA NR in 5GS. This option is particularly attractive for areas in which legacy LTE eNBs and the EPCs are ready to be upgraded to ngeNBs and the 5GCs.  From the point of
Read more

DC Carrier in NR

-
Image
Home                 LTE                NB-IoT               5G(NR-NSA) In this article, we will learn the basics of DC Carrier and why it is needed. Why in NR, DC subcarrier is not reserved like LTE? With legacy LTE (4G) it was decided that all devices (UE) should be capable of the maximum carrier bandwidth of 20MHz (UE can also support 10/15/5/3 MHz). This was a reasonable assumption at the time given the relatively modest bandwidth compared to NR, Whereas NR is designed to support very wide bandwidths up to 400MHz (for FR2) and 100Mhz (for FR1) for a single carrier. As well as NR supports multiple numerologies on the same transmitted carrier frequency. It is not necessary that all devices can support up to 400 MHz Bandwidth, hence in NR BWP concept is introduced. (To learn more about BWP Click here ). Note: in the above and below NR case figure, we assume that for each and every BWP have configured some  txDirectCurrentLocation  value.     As shown in the a
Read more

Authentication in LTE

-
Home                 LTE                NB-IoT            5G(NR-NSA)   What is Authentication and what type of Authentication is used in LTE? Authentication is a process by which both the UE and Network check whether the other party is authorized to communicate with them. In LTE and WCDMA, a mutual authentication process is used i.e. the Network checks whether the UE is authorized to camp on it and the UE also checks whether it is trying to camp on is the correct Network. The UE becomes authorized to camp on a network by subscribing to the network. In LTE, EPS AKA i.e. Authentication Key Agreement procedure is used for Mutual Authentication. Why is Authentication required from both sides in LTE? The UE needs to be authenticated by the NW to check whether it has subscribed to the NW or not. Only UEs which have a valid subscription should be allowed to camp on the NW. The NW should also be authenticated by the UE because if the UE does not check its
Read more

HARQ RTT Timer

-
Home                 LTE                NB-IoT            5G(NR-NSA)   Hi guys today we are focus on HARQ RTT timer in DL as well as UL for LTE and NB-IOT. What is HARQ RTT Timer? This parameter specifies the min amount of TTIs before a DL HARQ retransmission is expected by the UE. (3GPP TS 36.321 V8.0.0) Simple way to understand: the HARQ Round Trip Time (RTT) timer is defined for UE to sleep during HARQ RTT. When decoding DL TB for one HARQ fails, UE can next retransmission TB after at least HARQ RTT sub frames. While HARQ RTT timer is running, UE need not monitor PDCCH. At HARQ RTT timer expiry, UE resumes PDCCH reception. Two type of HARQ RTT timer is there. HARQ RTT Timer : This parameter specifies the minimum number of subframe(s) before a DL HARQ retransmission is expected by the MAC entity. (3GPP TS 36.321 version 13.3.0 Release 13) UL HARQ RTT Timer : This parameter specifies the minimum amount of subframe(s) before a UL HARQ retransmission grant is e
Read more