HARQ Basic Part-1

-
Home               LTE              NB-IoT             5G(NR-NSA)


In this section, we will learn about HARQ basic. 

What is ARQ?

ARQ stands for automatic repeat request. It refers to the re-transmission protocol in which the receiver checks for errors within the received data and if an error is detected then the receiver discards the data and request a re-transmission forms the sender. For acknowledged mode the RLC layer uses an ARQ protocol. 

What is HARQ?

HARQ stands for hybrid ARQ. It refers to a re-transmission protocol in which the receiver checks for errors in the received data and if an error is detected then the receiver buffers (soft buffers) the data and requests a retransmission from sender. HARQ receiver then is able to combine the buffered data with the re-transmitted data to channel decoding and error detection. This improves the performance of re-transmissions. HARQ re-transmissions can benefit from either chase combining or incremental redundancy.

What is the difference between ARQ and HARQ?

ARQ

HARQ
Works at RLC layer
Works at PHY layer but controlled by MAC layer

If there is an error in the received data (as detected by ARQ at RLC layer) then it is discarded, and a new retransmission is requested from the sender

If there is an error in the received data then the Receiver buffers the data (at PHY layer control by MAC) and requests a retransmission from the sender.



What is chase combining and its benefits?

Chase combining means that the physical layer applies the same puncturing pattern to both the original transmission and each retransmission. This results in re-transmissions which include the same set of physical layer bits as the original transmission. The benefits of chase combining are its lower UE memory requirement and simplicity.

What is incremental redundancy?

It means that the physical layer applies different puncturing patterns to the original transmission and retransmissions. Thus retransmission includes a different set of physical layer bits to the original transmission. The drawbacks here are increased UE memory requirement and complexity.

How LTE is HRQ is different from NR HARQ?

In LTE HARQ, downlink uses asynchronous mechanism and uplink uses synchronous mechanism. But in case of NR both downlink and uplink uses Asynchronous mechanism.

What is synchronous and asynchronous HARQ?

In synchronous HARQ retransmission for each process occur at predefined times relative to the initial transmission, thus no need to signal HARQ process number but can be inferred from transmission timing. In asynchronous HARQ, the retransmissions can occur at any time and HARQ process number (HARQ ID) is sent to correctly associate each retransmission with the corresponding initial transmission. Synchronous HARQ reduces signaling overhead while asynchronous HARQ increases flexibility in scheduling.

What is adaptive and non-adaptive HARQ?

The modulation, coding scheme, and frequency resource allocation may be changed at each retransmission in adaptive HARQ. While in non-adaptive HARQ, retransmissions are performed either by the same previous transmission attributes or by predefined rules. Adaptive HARQ brings more scheduling gain at the expense of signaling overhead.



In the next section, we will learn more about HARQ and its basic. So keep reading……. And Stay tune……………
Pinal Dobariya………..


reference:
38.321
38.322
36.321
36.322

Comments

Post a Comment

Popular posts from this blog

5G Deployment Option-3/3a/3x

-
Image
Home                 LTE                NB-IoT            5G(NR-NSA)   Hi Guys today we are learning about 5G deployment options, if you want to know more about other 5G deployment option please  click here Option 3: EN-DC (EUTRA-NR Dual Connectivity) Option 3 represents a network having both LTE and NR radio access, but using only the EPC core of LTE to route the Control signals. In this option, LTE is used as the control plane anchor for NR, and both LTE and NR are used for user data traffic.(user plane). It could also be called as Non-Standalone (NSA) NR in Evolved Packet System. The only difference between Options 3 and 3A is based on whether the user plane data is sent to NR directly or via the LTE RAN. This standardization was concluded in 3GPP Rel-15. This is a possible first step in the migration towards 5G-SA. This option will be most attractive for operators which have early deployments of 5G NR access systems in areas where legacy eNB and EPC a
Read more

Soft Handover vs Hard Handover

-
Home                 LTE                NB-IoT            5G(NR-NSA) Now before we move to other things like measurements in handover, handover decision, handover procedure, handover interruption time, and mobility robustness optimization, let us take a look into difference between soft handover and hard handover. Soft Handover Hard Handover The handover in which radio links are added and removed in a way that MS always keeps at least one radio link to the UTRAN is known as soft handover. The handover in which all the old radio links in MS are removed before the new radio links are established is known as hard handover. This can also be simplified as make before break This can also be simplified as break before make As call drop rate is lower this handover is used to lower the rate of call drop. In this case higher rates of call drops are found Why soft handover is not included
Read more

DRX (Discontinuous Reception)

-
Image
Home                 LTE                NB-IoT            5G(NR-NSA)   What is DRX and DRX active period? What channels does it monitor in active period? Data transmission between UE and their base stations(eNodeB) uses radio frames with10ms duration, where in each radio frame consists of 10 1ms( 1 frame=10ms duration=10 subframe) subframes. Physical Downlink Control Channel (PDCCH) at the beginning of each subframe indicates whether there is data for UE to receive or not. Devices has to monitor these PDCCHs in each subframe so that it can find out whether they carry any data to receive. Because devices do not receive data in every subframe, this monitoring process naturally leads to high battery consumption.  What is the purpose of DRX? The main purpose of DRX is to lower battery consumption when there is no UL/DL data. means, when there is no traffic(DL/UL) that time devices enter into sleep mode (with RF module turned off) for some period of time as configured by
Read more

DC Carrier in NR

-
Image
Home                 LTE                NB-IoT               5G(NR-NSA) In this article, we will learn the basics of DC Carrier and why it is needed. Why in NR, DC subcarrier is not reserved like LTE? With legacy LTE (4G) it was decided that all devices (UE) should be capable of the maximum carrier bandwidth of 20MHz (UE can also support 10/15/5/3 MHz). This was a reasonable assumption at the time given the relatively modest bandwidth compared to NR, Whereas NR is designed to support very wide bandwidths up to 400MHz (for FR2) and 100Mhz (for FR1) for a single carrier. As well as NR supports multiple numerologies on the same transmitted carrier frequency. It is not necessary that all devices can support up to 400 MHz Bandwidth, hence in NR BWP concept is introduced. (To learn more about BWP Click here ). Note: in the above and below NR case figure, we assume that for each and every BWP have configured some  txDirectCurrentLocation  value.     As shown in the a
Read more

5G Deployment Option-7/7a/7x

-
Image
Home                 LTE                NB-IoT            5G(NR-NSA) Hi Guys today we are learning about 5G deployment options, if you want to know more about other 5G deployment option please  click here Option 7: Deployment Option 7 represents a deployment scenario in which the Next Generation Core (NGC) will be used with a mixture of LTE and NR radio.  Next Generation signaling will be used but it will be routed via the LTE RAN because the LTE network is more fully built out and thus more reliable for handling signaling.  Options 7 and 7a differ on whether the user plane data is sent to NR directly or via the LTE RAN. 7/7A/7X require an eLTE upgrade of the existing LTE network at the start. (Difference is UP path Non Standalone ( Dual Connectivity 4G/5G ) Option 7/7A: NSA NR in 5GS. This option is particularly attractive for areas in which legacy LTE eNBs and the EPCs are ready to be upgraded to ngeNBs and the 5GCs.  From the point of
Read more

Authentication in LTE

-
Home                 LTE                NB-IoT            5G(NR-NSA)   What is Authentication and what type of Authentication is used in LTE? Authentication is a process by which both the UE and Network check whether the other party is authorized to communicate with them. In LTE and WCDMA, a mutual authentication process is used i.e. the Network checks whether the UE is authorized to camp on it and the UE also checks whether it is trying to camp on is the correct Network. The UE becomes authorized to camp on a network by subscribing to the network. In LTE, EPS AKA i.e. Authentication Key Agreement procedure is used for Mutual Authentication. Why is Authentication required from both sides in LTE? The UE needs to be authenticated by the NW to check whether it has subscribed to the NW or not. Only UEs which have a valid subscription should be allowed to camp on the NW. The NW should also be authenticated by the UE because if the UE does not check its
Read more

5G abbreviations

-
Image
Home                 LTE                NB-IoT            5G(NR-NSA)   As per readers request this article is based on some 5G abbreviations (PCell,spCell,Scell,PSCell,MCG.SCG,Master-Node,Secondary-Node) for better understanding. What is Master Node? Master node:  The node (radio access node) that provides the control plane connection to the core network in case of multi radio dual connectivity (MR-DC). For example, it can be master eNB in EN-DC, a Master ng-eNB in NGEN-DC What is Secondary Node? Secondary node:   the radio access node, with no control plane connection to the core network, providing additional resources to the UE in case of MR-DC. For example, It may be an en-gNB in EN-DC or a Secondary ng-eNB (in NE-DC). What is MCG? MCG: Master Cell group It is a group of serving cells associated with the Master Node, comprising of the PCell   and optionally one or more Scells.  (see figure shown above) MCG and SCG are concepts under
Read more